KODE2 RAHASIA HP KOMPLET!.gsm n cdma.(2)

Siemens C 25

Secret Codes

SP unlock *#0003*(secret code 8 digits)#

*#06# for checking the IMEI (International Mobile Equipment Identity)

Resets language to automatic selection : * # 0000 # then Green button

Pin Out

1- GND
2- SB
3- POWER
4- NC
5- TX
6- RX
7- CLOCK
8- DATA
9- GND MIC
10- HF MIC
11- AUDIO
12- GND AUDIO


Sagem MC959

Secret Codes

MC959

in main menu press * for hot-menu:
lcd, led, vibra, tests, imei, software versions, battery voltage

Type MENU - 5 - 1 - 1 - # to enter Engineering menu on SAGEM (RC-712, 721, 815 and 815 plus) phones.

Panasonic G500

IEMI:
To view IMEI number *#06#


--------------------------------------------------------------------------------

PINOUTS

1 - Ground
2 - TX_Audio
3 - Audio_Ground
4 - HF_ON (L=ON) -> L=H/F ON
5 - AOP_Sense <- Data Adaptor Select
6 - Serial_Up <- UART up (9600,33.8kbps)
7 - Serial_Down -> UART down
8 - External_Power <- POWER FOR CHARGING
9 - Ground
10 - RX_Audio
11 - Radio_Mute -> L=MUTE
12 - HF_Sense <- L=H/F MODE
13 - Reserved L=FLASH WRITE ENABLE
14 - Ignition <- H=ON
15 - Logic_Power -> H=HANDSET ON
16 - PAON -> Power Amplifier Control Signal.

Mitsubishi MT- D30

Secret Codes

Monitor mode: Hold C and press 379
Secret menu: Hold C and press 987
Version number: Hold C and press 597
Phase1 and 2 : Hold C and press 499
Warm start : Hold C and press 179
Instant turn off: Hold C and press 999
Unlock menu: Hold C and press 787090

Mitsubishi Trium

*#0000# to reset the phones menu-language to natural language, set initially by the distributor.

*#06# for checking the IMEI (International Mobile Equipment Identity)

hold * then 5806 - show software version
hold * then 5807 - a littel bit diffrent
hold * then 5472 - Testmode for datacable (it seems so)
hold * then 4329 - Activate and deactivate NETMONITOR
hold * then 621342 - Activate and deactivate another NETMONITOR
hold * then 3926 - shutdown

SP lock
You can turn around the lock routin by entering **04*PIN*PIN*PIN# now the secretcode change was applied and the software turns back to main menue. It works not on all triums, only on thos with older sofware versions.

SIEMENS S1 / S3 / S3 COM / S4

To view the software date and else with S3 com, S4, S4Power
press with SIM removed *#06# and left softkey.

To view some other stuff with S4Power
press with SIM removed *#06# and left softkey twice.

To view the software date with S3 com, S4, S4Power
press with SIM installed menu 98 and left softkey twice.

ACTIVATE MONITOR MODE

Siemens S1/S3

Menu, 9 (Phone Options), 7 (Phone Status), Left Display Button (left MENU key),
5553756, HangUp Button (Red HandSet key)

Siemens S3 COM/S4

Menu, 9 (Phone Options), 7 (Phone Status), Left Display Button
(left MENU key), 7684666, HangUp Button (Red HandSet key)

Note: Now Monitor should appear at the bottom of the Network Options menu.

MONITOR MODE

Pressing the right Display Button when in monitor mode will toggle into 1 and 2 modes

Pressing the right Display Button when in monitor mode will show a
list of the six cells with the strongest signals.

Test Mode Indicators: (* = only available when call in progress )

CH Channel Number

RX Signal Strength (dB)

N NCC (Colour Code)

B BCC (Colour Code)

CI Cell ID (in Hex)

C1+ How long before phone does forced hand over.(see RX and RXAM)

LAI Location Area Identity. Display Network ID code(42F010 = 240.01) and MSC

TXPWR Transmit Power (dB)

RXAM Receive signal strength cut-off point

TS* Time Slot Number

TA* Timing Advance. Distance from tower in Km X 2

PL* Power Level
SIEMENS S1

Here's a trick to play Tetris, also known as Klotz on a Siemens S1.
Turn the phone on. Enter PIN. Before the telephone has logged in to the
your GSM net do the following steps.

1: Choose F 9 (function settings)
2: Choose send own number and push the right button for choose.
3: Push 9

USE 2 as <> , rotate the klotz with 5 and drop with 4.